










The SuperATV Ready-Fit Winch for Can-Am Defender HD8 puts the main pieces of your recovery setup in one package. Choose a 4,500 lb. or 6,000 lb. Black Ops winch with 50-foot synthetic rope, a prewired solenoid, wired rocker switch, and wireless remote. It gives you a way to pull the machine out when mud, ruts, or a tough trail section stop your progress.
The 3/16-inch steel mount is built for the Defender HD8 models listed below. The prewired solenoid saves wiring work, whether you use your Defender around the property or take it out on the trails. The synthetic rope is light and easy to carry to an anchor, and the wired and wireless controls give you two ways to run the winch.
Includes:
- Black Ops winch in the selected 4,500 lb. or 6,000 lb. capacity
- 50-foot synthetic winch rope
- Preassembled solenoid and wiring for your machine
- Wireless remote and wired rocker switch
- Winch hook, pull strap, and rope stopper
- Vehicle-specific 3/16-inch steel mounting plate
- Aluminum hawse fairlead
- Installation hardware
Specifications
| Manufacturer | SuperATV |
|---|---|
| Product Type | Ready-Fit Recovery Winch Kit |
| Part Number(s) | QWM-CA-DEF20-4500#AB, QWM-CA-DEF20-6000#AB |
| Rated Line Pull | 4,500 lb. or 6,000 lb.; selected configuration |
| Motor | 12V permanent-magnet DC; 1.3 HP for 4,500 lb.; 1.9 HP for 6,000 lb. |
| Rope | 50-foot synthetic |
| Mount Material | 3/16-inch steel |
| Controls | Wired rocker switch and wireless remote |
| Published Remote Range | Up to 50 feet |
| Assembly | Prewired solenoid; vehicle-specific installation |
| Primary Application | UTV vehicle recovery |
| Gear Ratio | 166:1 (4,500 lb.); 266:1 (6,000 lb.) |
Available configurations:
| Part Number | Selection |
|---|---|
| QWM-CA-DEF20-4500#AB | Winch Size: 4500 lb. Winch |
| QWM-CA-DEF20-6000#AB | Winch Size: 6000 lb. Winch |
Fitment
| Make | Model | Year Range |
|---|---|---|
| Can-Am | Defender HD8 | 2020–2021 |
| Can-Am | Defender HD8 DPS | 2020–2021 |
| Can-Am | Defender HD8 XT | 2020–2021 |
| Can-Am | Defender MAX HD8 | 2020–2021 |
| Can-Am | Defender MAX HD8 DPS | 2020–2021 |
| Can-Am | Defender MAX HD8 XT | 2020–2021 |
FAQs
1. What does Ready-Fit mean?
The kit brings the winch, prewired solenoid, rope, and controls together so you spend less time gathering parts. The vehicle-specific mounting plate is included. You still need to bolt everything in place, route the wiring, and finish the electrical connections.
2. Should I choose the 4,500 lb. or 6,000 lb. winch?
Start with the loaded weight of your machine and the terrain you ride. Deep mud, steep hills, and buried tires take more pulling force than a machine rolling on level ground. The 6,000 lb. option offers more pulling capacity, but the mount, recovery points, and rigging still need to handle the load.
3. What should I know before installing this kit?
The 3/16-inch steel mount is built for the Defender HD8 models listed below. The prewired solenoid saves wiring work, whether you use your Defender around the property or take it out on the trails.
4. What does the synthetic rope need for upkeep?
Keep it clean and look it over for cuts, worn spots, and heat damage before a pull. Check the fairlead for sharp edges, protect the rope from rocks, and replace damaged line. Wear gloves and keep everyone clear while the rope is under tension.
5. Can I keep pulling until the machine is free?
Give the winch cooling breaks as directed in its manual. If the motor stalls or gets too hot, stop and work out what is holding the machine rather than keeping the switch pressed. A winch rope should never be used for a running-start pull.