{"product_id":"1350-1410-slip-driveshaft-builder-kit","title":"WOD 1350 Weld\/1410 Slip Driveshaft DIY Builder Kit","description":"\u003cp\u003eThe \u003cstrong\u003eWOD 1350 Weld \/ 1410 Slip Driveshaft DIY Builder Kit\u003c\/strong\u003e is a hybrid driveline solution for custom off-road vehicles that need a 1350-series weld yoke on one end and the added spline engagement and strength of a 1410-series slip assembly on the other. Built with \u003cstrong\u003egenuine Dana\/Spicer driveline components,\u003c\/strong\u003e this kit allows fabricators to build a custom-length front or rear driveshaft matched to the vehicle’s wheelbase, suspension travel, axle position, and drivetrain configuration.\u003c\/p\u003e\n\u003cp\u003eThis mixed-series configuration is commonly used when adapting existing 1350 driveline components to a stronger 1410 slip section, completing a custom drivetrain swap, or upgrading only part of an established driveline system. It is well suited for rock crawlers, trail buggies, Jeeps, and custom chassis builds where an off-the-shelf driveshaft will not provide the required component combination, length, or suspension travel.\u003c\/p\u003e\n\u003cp\u003e\u003cstrong\u003eIncludes:\u003c\/strong\u003e\u003c\/p\u003e\n\u003cul\u003e\n\u003cli\u003e(1) Genuine Dana\/Spicer Weld Stub\u003c\/li\u003e\n\u003cli\u003e(1) Genuine Dana\/Spicer 1350 Weld Yoke\u003c\/li\u003e\n\u003cli\u003e(1) Genuine Dana\/Spicer 1410 Slip Yoke\u003c\/li\u003e\n\u003c\/ul\u003e\n\u003cp\u003e\u003cstrong\u003eImportant:\u003c\/strong\u003e This is a DIY builder kit and does not come assembled. Final measuring, tube cutting, fitting, welding, balancing, and assembly are required.\u003c\/p\u003e\n\u003cp\u003e\u003cstrong\u003eOptional Components:\u003c\/strong\u003e Driveshaft tubing and compatible U-joints are available separately.\u003c\/p\u003e\n\u003chr\u003e\n\u003cdetails class=\"details\"\u003e\n\u003csummary class=\"details__header\"\u003e\u003cstrong\u003eSpecifications\u003c\/strong\u003e\u003cspan class=\"svg-wrapper icon-plus\"\u003e\u003csvg xmlns=\"http:\/\/www.w3.org\/2000\/svg\" fill=\"none\" viewbox=\"0 0 14 14\" width=\"14\" height=\"14\"\u003e\u003cpath class=\"vertical\" d=\"M2.75 7H11.25\" stroke=\"currentColor\" stroke-width=\"var(--icon-stroke-width)\" stroke-linecap=\"round\"\u003e\u003c\/path\u003e\u003cpath class=\"horizontal\" d=\"M7 2.75L7 11.25\" stroke=\"currentColor\" stroke-width=\"var(--icon-stroke-width)\" stroke-linecap=\"round\"\u003e\u003c\/path\u003e\u003c\/svg\u003e\u003c\/span\u003e\u003c\/summary\u003e\n\u003cdiv class=\"details-content rte\"\u003e\n\u003ctable class=\"custom-specs-table\"\u003e\n\u003ctbody\u003e\n\u003ctr\u003e\n\u003cth\u003eSpecification\u003c\/th\u003e\n\u003cth\u003eDetails\u003c\/th\u003e\n\u003c\/tr\u003e\n\u003ctr\u003e\n\u003ctd\u003eManufacturer\u003c\/td\u003e\n\u003ctd\u003eWide Open Design\u003c\/td\u003e\n\u003c\/tr\u003e\n\u003ctr\u003e\n\u003ctd\u003eComponent Manufacturer\u003c\/td\u003e\n\u003ctd\u003eDana\/Spicer\u003c\/td\u003e\n\u003c\/tr\u003e\n\u003ctr\u003e\n\u003ctd\u003eProduct Type\u003c\/td\u003e\n\u003ctd\u003eHybrid DIY Driveshaft Builder Kit\u003c\/td\u003e\n\u003c\/tr\u003e\n\u003ctr\u003e\n\u003ctd\u003eWeld-End U-Joint Series\u003c\/td\u003e\n\u003ctd\u003e1350\u003c\/td\u003e\n\u003c\/tr\u003e\n\u003ctr\u003e\n\u003ctd\u003eSlip-End U-Joint Series\u003c\/td\u003e\n\u003ctd\u003e1410\u003c\/td\u003e\n\u003c\/tr\u003e\n\u003ctr\u003e\n\u003ctd\u003eRecommended Tube Size\u003c\/td\u003e\n\u003ctd\u003e2.5\" OD x .250\" Wall DOM\u003c\/td\u003e\n\u003c\/tr\u003e\n\u003ctr\u003e\n\u003ctd\u003eApplication\u003c\/td\u003e\n\u003ctd\u003eHeavy-Duty Off-Road and Hybrid Driveline Builds\u003c\/td\u003e\n\u003c\/tr\u003e\n\u003ctr\u003e\n\u003ctd\u003eAssembly Required\u003c\/td\u003e\n\u003ctd\u003eYes\u003c\/td\u003e\n\u003c\/tr\u003e\n\u003ctr\u003e\n\u003ctd\u003eInstallation\u003c\/td\u003e\n\u003ctd\u003eFabricator Installed\u003c\/td\u003e\n\u003c\/tr\u003e\n\u003ctr\u003e\n\u003ctd\u003eTube Included\u003c\/td\u003e\n\u003ctd\u003eOptional\u003c\/td\u003e\n\u003c\/tr\u003e\n\u003ctr\u003e\n\u003ctd\u003eU-Joints Included\u003c\/td\u003e\n\u003ctd\u003eOptional\u003c\/td\u003e\n\u003c\/tr\u003e\n\u003ctr\u003e\n\u003ctd\u003eFinal Balancing Required\u003c\/td\u003e\n\u003ctd\u003eYes\u003c\/td\u003e\n\u003c\/tr\u003e\n\u003c\/tbody\u003e\n\u003c\/table\u003e\n\u003c\/div\u003e\n\u003c\/details\u003e\n\u003chr\u003e\n\u003cdetails class=\"details\"\u003e\n\u003csummary class=\"details__header\"\u003e\u003cstrong\u003eFitment\u003c\/strong\u003e\u003cspan class=\"svg-wrapper icon-plus\"\u003e\u003csvg xmlns=\"http:\/\/www.w3.org\/2000\/svg\" fill=\"none\" viewbox=\"0 0 14 14\" width=\"14\" height=\"14\"\u003e\u003cpath class=\"vertical\" d=\"M2.75 7H11.25\" stroke=\"currentColor\" stroke-width=\"var(--icon-stroke-width)\" stroke-linecap=\"round\"\u003e\u003c\/path\u003e\u003cpath class=\"horizontal\" d=\"M7 2.75L7 11.25\" stroke=\"currentColor\" stroke-width=\"var(--icon-stroke-width)\" stroke-linecap=\"round\"\u003e\u003c\/path\u003e\u003c\/svg\u003e\u003c\/span\u003e\u003c\/summary\u003e\n\u003cdiv class=\"details-content rte\"\u003e\n\u003cp\u003e\u003cstrong\u003eUniversal Fitment for Custom Driveshaft Fabrication\u003c\/strong\u003e\u003c\/p\u003e\n\u003cp\u003e\u003cstrong\u003eCommon Applications:\u003c\/strong\u003e\u003c\/p\u003e\n\u003cul\u003e\n\u003cli\u003eRock crawlers\u003c\/li\u003e\n\u003cli\u003eTrail buggies\u003c\/li\u003e\n\u003cli\u003eOff-road race vehicles\u003c\/li\u003e\n\u003cli\u003eOne-ton Jeep builds\u003c\/li\u003e\n\u003cli\u003eCustom tube chassis vehicles\u003c\/li\u003e\n\u003cli\u003eFront driveshafts\u003c\/li\u003e\n\u003cli\u003eRear driveshafts\u003c\/li\u003e\n\u003cli\u003eMulti-piece driveshaft systems\u003c\/li\u003e\n\u003cli\u003eCustom drivetrain swaps\u003c\/li\u003e\n\u003cli\u003eBuilds using mixed 1350 and 1410 driveline components\u003c\/li\u003e\n\u003c\/ul\u003e\n\u003cp\u003e\u003cstrong\u003eThis Configuration Is Commonly Used When:\u003c\/strong\u003e\u003c\/p\u003e\n\u003cul\u003e\n\u003cli\u003eThe axle or pinion end requires a 1350-series weld yoke.\u003c\/li\u003e\n\u003cli\u003eThe drivetrain requires a 1410-series slip assembly.\u003c\/li\u003e\n\u003cli\u003eAn existing 1350 driveline is being upgraded without replacing every component.\u003c\/li\u003e\n\u003cli\u003eAdditional spline engagement or slip-section strength is needed.\u003c\/li\u003e\n\u003cli\u003eA custom drivetrain combination cannot be matched with a single-series driveshaft kit.\u003c\/li\u003e\n\u003c\/ul\u003e\n\u003cp\u003e\u003cstrong\u003eFitment Notes:\u003c\/strong\u003e\u003c\/p\u003e\n\u003cul\u003e\n\u003cli\u003eThis is a universal builder kit and is not supplied for a predetermined finished length.\u003c\/li\u003e\n\u003cli\u003eConfirm that the 1350 weld end and 1410 slip end match the corresponding drivetrain components before ordering.\u003c\/li\u003e\n\u003cli\u003eMeasure the vehicle at ride height and through the full suspension cycle before cutting the driveshaft tube.\u003c\/li\u003e\n\u003cli\u003eConfirm sufficient slip travel at full compression, full droop, and maximum axle articulation.\u003c\/li\u003e\n\u003cli\u003eVerify compatibility with the transmission or transfer-case output, axle yoke, pinion yoke, carrier bearing, and U-joint retention style.\u003c\/li\u003e\n\u003cli\u003eConfirm driveshaft operating angles and available chassis clearance before final welding.\u003c\/li\u003e\n\u003cli\u003eFinal welding should be completed by an experienced driveline fabricator.\u003c\/li\u003e\n\u003cli\u003eThe completed driveshaft must be checked for runout and professionally balanced before operation.\u003c\/li\u003e\n\u003c\/ul\u003e\n\u003c\/div\u003e\n\u003c\/details\u003e\n\u003chr\u003e\n\u003cdetails class=\"details\"\u003e\n\u003csummary class=\"details__header\"\u003e\u003cstrong\u003eFAQ\u003c\/strong\u003e\u003cspan class=\"svg-wrapper icon-plus\"\u003e\u003csvg xmlns=\"http:\/\/www.w3.org\/2000\/svg\" fill=\"none\" viewbox=\"0 0 14 14\" width=\"14\" height=\"14\"\u003e\u003cpath class=\"vertical\" d=\"M2.75 7H11.25\" stroke=\"currentColor\" stroke-width=\"var(--icon-stroke-width)\" stroke-linecap=\"round\"\u003e\u003c\/path\u003e\u003cpath class=\"horizontal\" d=\"M7 2.75L7 11.25\" stroke=\"currentColor\" stroke-width=\"var(--icon-stroke-width)\" stroke-linecap=\"round\"\u003e\u003c\/path\u003e\u003c\/svg\u003e\u003c\/span\u003e\u003c\/summary\u003e\n\u003cdiv class=\"details-content rte\"\u003e\n\u003ch3\u003eWhy use a 1350 weld yoke with a 1410 slip yoke?\u003c\/h3\u003e\n\u003cp\u003eThis combination allows the driveshaft to retain compatibility with a 1350-series component at the weld end while using a larger 1410-series slip assembly. It is useful when adapting mixed drivetrain components or upgrading the slip section without replacing the complete driveline.\u003c\/p\u003e\n\u003ch3\u003eWhat is the advantage of the 1410 slip assembly?\u003c\/h3\u003e\n\u003cp\u003eThe 1410 slip section provides a larger driveline platform with increased spline engagement and additional strength in the area responsible for driveshaft plunge. This can be beneficial in long-travel suspension systems that place substantial movement and shock load on the slip assembly.\u003c\/p\u003e\n\u003ch3\u003eDoes the 1410 slip end make the entire driveshaft as strong as a full 1410 system?\u003c\/h3\u003e\n\u003cp\u003eNo. A hybrid driveshaft remains limited by its weakest component. The 1350 weld yoke, tubing, welds, U-joints, slip assembly, operating angles, and connected drivetrain components all affect the capacity of the finished system.\u003c\/p\u003e\n\u003ch3\u003eWhich U-joints are required?\u003c\/h3\u003e\n\u003cp\u003eThe weld end requires a compatible 1350-series universal joint, while the slip end requires a compatible 1410-series universal joint. Verify the mating yokes and retention style at both ends before ordering components.\u003c\/p\u003e\n\u003ch3\u003eDoes this kit arrive assembled?\u003c\/h3\u003e\n\u003cp\u003eNo. This is a DIY builder kit intended for experienced fabricators. Final measuring, tube cutting, fitting, welding, balancing, and assembly are required before installation.\u003c\/p\u003e\n\u003ch3\u003eWhat driveshaft tubing is recommended?\u003c\/h3\u003e\n\u003cp\u003eMany off-road builders use 2.5\" OD x .250\" wall DOM tubing because it offers strong resistance to dents, torsional deformation, and rock damage. Final tubing selection should also consider finished shaft length, operating RPM, critical speed, vehicle weight, and available clearance.\u003c\/p\u003e\n\u003ch3\u003eHow much slip travel should the driveshaft have?\u003c\/h3\u003e\n\u003cp\u003eThe required slip travel depends on suspension geometry and axle movement. The slip assembly must remain safely engaged at full droop while retaining enough compression travel to prevent bottoming out when the suspension reaches full compression.\u003c\/p\u003e\n\u003ch3\u003eCan I weld the driveshaft without balancing it afterward?\u003c\/h3\u003e\n\u003cp\u003eNo. Even a carefully fitted and welded shaft can have runout or weight imbalance. The completed driveshaft should be checked for straightness and professionally balanced before operation to reduce vibration and protect bearings, seals, transfer-case outputs, and pinion components.\u003c\/p\u003e\n\u003ch3\u003eWhat other driveshaft configurations does Wide Open Design offer?\u003c\/h3\u003e\n\u003cp\u003eWide Open Design offers several configurations for different drivetrain combinations and load requirements:\u003c\/p\u003e\n\u003cul\u003e\n\u003cli\u003e\u003ca href=\"\/products\/1350-drive-shaft-builder-kit\"\u003e1350 Weld\/Slip Driveshaft Builder Kit\u003c\/a\u003e\u003c\/li\u003e\n\u003cli\u003e\u003ca href=\"\/products\/wod-1410-driveshaft-builder-kit\"\u003e1410 Weld\/Slip Driveshaft Builder Kit\u003c\/a\u003e\u003c\/li\u003e\n\u003cli\u003e1480 Weld\/Slip Driveshaft Builder Kit\u003c\/li\u003e\n\u003cli\u003e1350 Weld\/1410 Slip Hybrid Driveshaft Builder Kit\u003c\/li\u003e\n\u003cli\u003e\u003ca href=\"\/products\/1410-1350-hybrid-slip-driveshaft-kit\"\u003e1410 Weld\/1350 Slip Hybrid Driveshaft Builder Kit\u003c\/a\u003e\u003c\/li\u003e\n\u003c\/ul\u003e\n\u003c\/div\u003e\n\u003c\/details\u003e\n\u003chr\u003e","brand":"Wide Open Design","offers":[{"title":"Default Title","offer_id":54642147229971,"sku":"WF03000B","price":369.99,"currency_code":"USD","in_stock":true}],"thumbnail_url":"\/\/cdn.shopify.com\/s\/files\/1\/1000\/1956\/8915\/files\/WF03000B-1350-1410-Slip-Hybrid-Driveshaft-Builder-Kit-1_32fa826d-d293-49a0-96e8-558874af45cc.jpg?v=1788289762","url":"https:\/\/kohparts.com\/products\/1350-1410-slip-driveshaft-builder-kit","provider":"KOHParts.com","version":"1.0","type":"link"}